 |  |
 |
177 Fulford Dr. Harkers Island, NC 28531 1-800-562-2742 (252) 504-3355 |
|
Specialty Tools  SIE18-79817 Engine Puller UniversalUniversal Engine Puller Fits 2 BBL and 4 BBL manifolds Replaces Mallory 9-79817 $49.95 SMI01117 Oil - Fuel Filter WrenchThis handy wrench removes screw on type marine water separator fuel filters and most oil filters Tough, forged stainless steel $22.95 GLM90260 Pinion Bearing Installation Tool for Mercruiser 91-38628TPinion Bearing Installation Tool to precisely fit the pinion bearing (must remove paper cone) to avoid crooked seating that causes gears to break or make noise on Mercruiser Drives. This item... $28.95 SMI01112 Propeller Nut Wrench (Metal) Mercury, Mariner, and MercruiserIncludes nut and 2 tab washers, Removes and Installs all Mercury Outboards (65 HP and up); Mercruisers (110 - 260 HP) Standard Units Wrench replaces 91-95830A1; Nut replaces 11-52707; Tab Washers... $15.95 SIE18-79820-1 Puller Gimbal Bearing Removal Tool for Mercruiser OMC Volvo Sierra 18-79820 SIE18-79820-1Gimbal Bearing Puller Tool for Mercruiser, OMC and Volvo Penta sterndrives. Sometimes the gimbal bearing can be a real pain to remove. This tool is designed to get the toughest gimbal bearing out.... $269.95 SIE18-9781 Pump Oil for Lower Unit Fits Quart BottlesOil Pump for Quart bottle, 4 cc pump and 3/8" - 16 swivel metal marine filler fitting. Ideal for adding Gear Lube and other fluids to small engines and marine lower units. Flexible Hose for... $15.95 GLM90110 Shift Cable Tool for Installation Removal of Mercruiser Shift Cables 91-12037Shift Cable Tool for Mercruiser Sterndrives. It will install and remove shift cables on Mercruiser 1, R, MR, & Alpha One Generation 2 Drives that have the cable coming in from the rear. The shift... $29.95 MAL9-79816 Tester Ethanol Fuel Mercury 91-879172T28Tester for Ethanol percentage. Replaces: Mercury 91-879172T28 Instructions: Fill with water to the line, fill with gas to the neck, put lid on and shake vigorously, stand vertical with cap on, let... $6.95 SIE18-79813 Tool Bearing Carrier Puller for Mercruiser Mercury YamahaBearing Carrier Puller Tool For: Mercruiser, Mercury, and Yamaha Replaces Mallory # 9-79813 $249.95 GLM90095 Tool Bearing Carrier Puller Remover I/O and OutboardBearing Carrier Puller, capacity: 5 tons for Mercruiser, Mercury/Mariner all style bearing carriers & most propellers. Jaws can be turned for pulling in the inside or outside. Also has locking bolts... $89.95 SIE18-9809 Tool Bearing Carrier Retainer Mercruiser Bravo 91-17257Bearing Carrier Retainer Tool for Mercruiser Bravo Drives Replaces: Mallory 9-79810 Mercury Marine 91-17257 $179.99 GLM90190 Tool Bearing Carrier Retainer wrench Lower Unit Mercruiser 91-61069TBearing Carrier Retainer Tool removes and installs bearing carrier retainer nuts on Mercruiser Bravo One, MC-I, R MR; and Alpha One, Gen. II; and TRS; drive units and Mercury Mariner Outboards with 4... $79.95 GLM90360 Tool Bellow Expander for Mercruiser Alpha 1 Bravo 91-45497A1 GLM90360Bellows Expander Tool which installs the exhaust bellows on the MC-1, R-MR, Alpha One, Bravo 1, Bravo 2 and Blackhawk drive Units. To use this tool on pre-Alpha, Alpha and Gen II Models, the upper... $69.95 GLM90470 Tool Bellow Sleeve Installer Mercruiser Bravo Alpha 1 Gen 2 91-818162U-Joint Bellow Sleeve Installation Tool Installs the aluminum sleeve in the u-joint bellows of all Bravo, Alpha One/Gen II, Blackhawk drive units Replaces #:91-818162; Sierra #... $49.95 SIE18-9870Tool Bellow Sleeve Installer Mercruiser Bravo Alpha 1 Gen 2 91-818162 SIE18-9870U-Joint Bellow Sleeve Installation Tool Installs the aluminum sleeve in the u-joint bellows of all Bravo, Alpha One Gen II, Blackhawk drive units Replaces #:91-818162; Sierra # 18-9870 $34.95 GLM90170 Tool Drive Gear Shimming for Mercruiser R MR Alpha and Gen 2 91-60523Drive Gear Shimming Tool that measures upper unit drive gear clearance on Mercruiser 1, R, MR, Alpha One Gen. II Drives. Replaces Merc. OEM: 91-60523. $129.95 GLM90220 Tool Drive Shaft Adapter for Mercruiser 91-56775TDrive Shaft Adapter provides a wrench surface to turn the drive shaft on Mercruiser 1, R, MR, Alpha One Gen.II drive units and many outboard engines with a 13 spline drive shaft. Replaces Merc. OEM:... $26.95 GLM90240 Tool Drive Shaft Bearing Retainer Wrench for Mercruiser 91-43506Drive Shaft Bearing Retainer Wrench removes and installs threaded bearing retainer under the water pump housing on Mercruiser sterndrives and Mercury Mariner outboards. OEM: 91-43506 Was:$36.95 $34.95 New Lower Price SIE18-9874 Tool Drive Shaft Preload For Mercruiser and Mercury 91-14311A2Drive Shaft Preload Tool. Preloads drive shaft bearing when checking pinion height and backlash on MC-I, R-MR, Alpha One, Alpha One/ Gen II drive units and outboards. Replaces: Mercury Marine... $169.95 GLM90270 Tool Driver Head for Mercruiser and Mercury Lower Unit 91-36569TDriver Head Specialty Tool which removes pinion bearing from MC-1, R-MR, and Alpha One drive units Replaces OEM: 91-36569T $14.95 GLM90050 Tool Engine Alignment for Mercruiser OMC Cobra SX Volvo SX 91-57797A3Engine Alignment Tool that can be used on Mercruiser OMC Cobra OMC SX and Volvo SX stern drives to align the drive to the engine during installation. IF your unit is not aligned properly you WILL... $89.95 GLM90180 Tool for Mercruiser Upper Unit Driven Gear Shimming 1 R MR Alpha Gen 2 91-60526TDriven Gear Shimming Tool for a Mercruiser Outdrive. This tool is used to measure the upper driven gear clearance. It will work on the following applications: Mercruiser Models MC-1/R/MR/Alpha... $218.95 SIE18-79814 Tool Fuel Filter for Mercury Verado and Optimax Engines 91-896661Fuel Filter Tool to remove and install the fuel filter on Optimax and Verado model motors. Replaces: Mercury Marine 91-896661 $6.95 SIE18-79825 Tool Gimbal Bearing Installer Mercruiser OMC Volvo SIE18-79825Installation Tool for Gimbal Bearings on Mercruiser, OMC and Volvo Penta SX sterndrives $44.95 SIE18-9861 Tool Hinge Pin for Mercruiser 1 MR Alpha and Bravo Outvrive 91-78310Hinge Pin Installation/Removal tool. Removes/installs hinge pins for all Mercruiser drive units. The hinge pin connects the bell housing to the gimbal ring and allows the unit to tilt. You normally... $15.95 ... more info Replacement Available GLM90200 Tool Hinge Pin Removal Install Mercruiser Replaces 91-78310Hinge Pin Installation/Removal tool. Removes/installs hinge pins for all Mercruiser drive units. The hinge pin connects the bell housing to the gimbal ring and allows the unit to tilt. You normally... $15.95 GLM90295 Tool Lower Unit Pinion Bearing Installer and Removal Set MercruiserPinion Bearing Removal and Installation Tool Assembly. Installs and removes pinion bearing on Mercruiser MC-1, R-MR, and Alpha One Lower units Kit Includes: GLM90260 Pinion Bearing Install Tool... $72.95 GLM90160 Tool Pinion Gear Shimming for Mercruiser 1 R MR Alpha Mercury V6 91-56048001Pinion Gear Shimming Tool to measure pinion height of Mercruiser 1, R, MR Alpha One and Alpha 1 Generation 2 Drive Sterndrive Units and Mercury / Mariner V6 Outboard Gearcases. Replaces Mercury... $199.95 SIE18-9841 Tool Pinion Gear Shimming for Mercruiser Bravo 1 Drives 1-42840TTool Pinion Gear Shimming for Mercruiser Bravo 1 Drives Shimming Tool Replaces: Mercury Marine 91-42840T Description: Shims pinion gear on Bravo One drives. $179.95 GLM90210 Tool Pinion Nut Adapter Lower Unit Mercruiser R MR Alpha 91-61067A3Pinion Nut Adapter Kit which holds the pinion nut when removing the pinion gear and drive shaft on Mercruiser MC-I, R-MR, and Alpha One drive units. Comes with one GLM90220 drive shaft adapter OEM:... $148.95 GLM90230 Tool Propeller Shaft Adapter Mercury Mariner Mercruiser 91-61077TPropeller Shaft Adapter. It provides a wrench surface to turn the propeller shaft on Mercruiser 1, R, MR, Alpha One Gen. II Bravo 1 & TRS drive units. Replaces Merc. OEM: # 91-61077T. $39.95 GLM90280 Tool Puller Rod for Mercruiser Lower Unit Drive Shaft 91-31229Puller Rod used with GLM90260 and GLM90270 tools to install and remove pinion bearing on Mercruiser Drives OEM: 91-31229 $19.95 SIE18-9810 Tool Shift Cable Adjustment for Mercruiser Bravo 91-17262A1Tool Shift Cable Adjustment for Mercruiser Bravo Fits the Following Applications Mercruiser Bravo Outdrive Adjustment Tool Replaces: Mercury 91-17262A1 Description: Used to install shift cable core... $34.95 GLM90140 Tool Shift Shaft Bushing for Mercruiser 1 R MR Alpha One Outdrives 91-31107TShift Shaft Bushing Tool for Mercruiser Sterndrives. It removes and installs the Bushings in the gearcase of the following Drive units: MC-1/R/MR/Alpha one. Replaces Mercruiser OEM: # 91-31107T. $18.95 GLM90290 Tool Spacer for MercruiserSpacer Fits GLM90280 to install pinion bearing on Mercruiser Drives $22.95 SIE18-9844 Tool Tapered Insert for Mercruiser Bravo Gimbal Water Hose 91-43579Tapered Insert Tool for installing the plastic water inserts in the Bravo gimbal water hose. Replaces: Mercury Marine 91-43579 $24.95 MER91-818162 Tool U-Joint Bellow Sleeve Installer for Mercruiser Alpha Gen 2 Bravo 91-818162 MER91-818162U-Joint Bellow Sleeve Installation Tool for Mercruiser Alpha Gen 2 and Bravo Outdrives. The later design bellows for the Gen 2 and Bravo drives us a hose clamp on one side and and internal sleeve on... $45.95 GLM90490 Tool Wrench Bearing Carrier Retainer for Mercruiser Bravo 2 and 3 91-17257TBearing Carrier Retainer Wrench for Mercruiser Bravo 2 & 3 outdrives Removes and installs lower unit bearing carrier retainer nuts on Bravo II and Bravo III drive units . Replaces Mercury Marine part... $158.95 GLM90070 Trailering Clips for Mercruiser MC-1 R, MR Alpha, Bravo GLM90070Trailering Clips for most Mercruiser outdrives. These slip over the trim ram to take the shock off of the trim system while trailering your boat. Fits: MC-1, R, MR, Alpha & Bravo. Replaces... $20.95 MAL9-79801 Wrench Bearing Retainer Spanner Nut Tool for Mercruiser 1 R MR Alpha 1This Wrench removes the Top Spanner Nut on Mercruiser # 1, R, MR, Alpha One, and Generation 2 Outdrives. This is needed to change the seals and to remove the gears in the upper unit. This tool also... $60.95 ... more info Replacement Available GLM90100 Wrench Bearing Retainer Spanner Nut Tool for Mercruiser 1 R MR Alpha 1 GLM90100This Wrench removes the Top Spanner Nut on Mercruiser # 1, R, MR, Alpha One, and Generation 2 Outdrives. This is needed to change the seals and to remove the gears in the upper unit. This tool also... $79.95 GLM90065 Wrench Propeller Floating for Mercruiser Mercury Mariner Force Honda 1 1/161-1/16" Propeller Wrench Kit (blue) for Mercury/Mariner/Force V4 & V6, 75, 90, 100, 115, 125, 135, 150, 175, 200, 225, 250 HP; all Mercruiser; Honda BF75-BF130 comes with GLM21271 OEMs: Mercury:... $18.95 Monthly Specials For May |
ebasicpower.com is © 1999-
Basic Power Industries, Inc., all rights reserved • All Item specifications and availability are
subject to change without notice
Basic Power Industries, Inc.• 177 Fulford Dr, Harkers Island, NC 28531-9520, US • +1-252-504-3355
Basic Power Industries, Inc.• 177 Fulford Dr, Harkers Island, NC 28531-9520, US • +1-252-504-3355