Drive Damper for Volvo Penta using a ZF or Hurth Tranmission. Fits Transmissions with a 10 spline input shaft. HAS THREE DIFFERENT SIZE SPRINGS. Replaces Volvo Penta original equipment part # 841892-3 Fits Diesel Engines MD21B AQD21B Gasoline Engines AQ115A AQ115B AQ130 AQ130A AQ130B AQ130C AQ130D AQ165A AQ170A AQ170B AQ170C AQD21A BB115A BB115B BB115C BB165A BB170A BB170B BB170C MB20A MB20B MB20C MD21A B20
Damper Drive Plate for Small Block 5.7L V8 For Crusader, Mercruiser and Volvo Penta applications Genuine Crusader part # R140019 Note: Genuine Crusader Parts are not always painted "Crusader Blue"
$289.95... more info
New Old Stock Drive Damper Diesel 26 Spline for 11.5 SAE Flywheel 13.875 Diameter Centa marine (drive plate, Centaflex dual stage coupling) for marine diesel engines with SAE 11.5 flywheel and 26-spline transmission. Centa part number: CF-DS-25-SAE11-1/2 Hurth ZF part number: 3311316004 Commonly used on these ZF and Hurth transmissions: 45C (HSW 450D) 63C (HSW 630D) 25 (HSW 250H) 25A (HSW 250A) 45-1 (HSW 450H2) 45A (HSW 450A2) 45IV 63 (HSW 630H1) 63A (HSW 630A1) 63IV (HSW 630V1) New Old Stock! May have some surface blemishes, but will work as new.
$499.95... more info
Drive Damper Assembly for Hurth Marine 122 mm Outside Diameter X 111 mm bolt circle center. 10 Spline 10/23/29 Teeth DIN 5464; 45° X 8 Replaces Hurth original equipment part # 254750.
Velvet Drive Heavy Duty Torisonal Drive Plate, AS3-K2C for Diesel Engines. Drive Plate is 15" diameter, full-circle, 26-spline, 8 Heavy Duty springs. Replaces Orginal equipment Velvet Drive and Borg Warner part numbers 1004-650-005 and 10-04-650-005. This is an original Velvet Drive Part.
Hurth Drive Damper Assembly 6-3/16" X 1-11/32" Diameter, 5 Bolt Holes, 6 Springs, 26 Teeth, 157mm OD Replaces: Hurth original equipment part # 3307316002; Sachs # 1866-061-002
$399.00... more info
Drive Damper Assembly 262 / 305 / 350, Crusader Supersedes the following numbers: CRU96225 , CRU97171Fits The Following Crusader Applications: C305 / 350 CID V8C220 (305 C.I.D.)C270 (350 C.I.D.) Note: Genuine Crusader Parts are not always painted "Crusader Blue"
$83.99... more info
Drive Damper Assembly, Crusader Supersedes the following numbers: CRU96710Fits The Following Crusader Applications: C454 (454 C.I.D.) V-8CM454XL Note: Genuine Crusader Parts are not always painted "Crusader Blue"
$109.95... more info
Drive Damper Flex Plate Assembly for Hurth and Borg Warner Velvet Drive Marine Transmissions. Fits many Hurth small Transmissions. Fits Perkins 4-108 and Chris Craft Flywheel Forward Engines that use a 10 Spline Transmission uss 5 attaching bolts. 157 mm Outside Diameter 6.18 Inches 5.5 Inch Bolt Circle Diameter for 10 Spline Input Shaft. Typical applications include: Hurth HBW gearboxes HBW5, HBW10, HBW15, HBW35, HBW50, HBW100, HBW125, HBW150 ZF gearboxes ZF5, ZF10, ZF12, ZF15 Technodrive TMC30, TMC40, TMC50 & TMC60 PRM Gearboxes PRM80, PRM120, PRM150 Borgwarner 500 DIN 5464; 72° X 5 Replaces Hurth original equipment part # 288240
Drive Damper Flex Plate Assembly for Velvet Drive 71, 72 and paragon with 26 spline input shaft. Used on Chris Craft and Flagship Flywheel Forward Engines and some Perkins and Westerbeke Diesel applications. 6.18 Inch Outside Diameter, 1.353 Spline, 26 tooth OEMs: Velvet Drive 1004-650-002 Velvet Drive AS4-K1C Westerbeke: 11618
Round type Damper Plate for Small Block V8 Springs: 8 Outside Dia: 7.125" Bolt Circle 6.58" Bolt Holes: 9 Genuine Velvet Drive Part # 070-008-1918 Replaces AS7-K1C
$199.95... more info
DRIVE DAMPER FLEX PLATE DETROIT DIESEL AND OTHER MARINE APPLICATIONS. 26 SPLINE 10.25 INCH DIAMETER 8 HOLE 9.5 INCH ON CENTER BOLTS GM PART NUMBER: 5133530
$417.88... more info
Drive Damper Flex Plate. Fits ZF and Hurth 26 Spline Marine Transmissions. 5.962" / 151.44 mm Outside Diameter 1-1/4" Diameter (spline) 8 bolt holes 6 springs 26 teeth 5.59" / 142 mm from center to center of bolt holes Replaces Hurth ZF part # 1866-052-002
Triangular Drive Damper Assembly for Velvet Drive Marine Tranmissions. Fits most GM with a 14" flywheel. Common use 6.66" RAD. (triangle) 1.353 Spline 26 Tooth. Fits most GM based marine engines with a 14 inch flywheel. This item replaces Borg Warner #s: 1004-650-006 AS4-K2C.
Round Drive Damper Assembly with Purple Springs for Velvet Drive 71, 72,1004, 1005, 1013, 1014 Series Marine Transmissions. Commonly used on almost all small block 305 350 and big block marine engines 427 454. Used by Mercruiser Volvo Crusader Marine Power and Chris Craft who all used the Velvet Drive Marine Transmission. Also used on many light to medium duty diesel engines. If you are unsure of the fitment, please refer to the dimensional drawing which gives all possible measurements. Also Used on Paragon Marine transmissions. Has a 26 tooth female spline. Fits all GM engines with 14 Inch flywheel. If you do not know the diameter of your GM Engine flywheel you can look at your starter. If your starter is top mount above the transmission or your bottom mount starter is held on with two long bolts rather than 1 long and 1 short bolt, then you have a 14 inch flywheel. 13.25" OD, 1.353 Spline; 26 Tooth. common use Replaces These OEMs: Borg Warner: 1004-650-007 Velvet Drive: AS7-K2C Crusader: 97334 Mercruiser: 47608A1
Drive Damper Flex Plate Assembly for GM 53 Series Detroit Diesel. 8 Inch outside diameter and 7.12 Inch bolt circle with 8 equally spaced mounting holes and 26 spline input. Velvet Drive 71 & 72 and 73 Series. This item replaces Borg Warner # 1004-650-003
Drive Damper Flex Plate Assembly for Hurth Marine 10 Spline Transmissions. 152 mm (Outside Diameter 5.98 Inches) X 123 mm (Bolt Circle Diameter 4.84 Inches) 10/23/29 Teeth DIN 5464; 45° X 8 Velvet Drive with Dowel Pins. Replaces Borg Warner OEM: 2301-650-001 Sachs 1866 052 001 Hurth OEM: 947-44-601-03, 254762.
Drive Damper for Westerbeke Marine Diesel Engines that use the Paragon SAO and P series Paragon that have the 26 Spline input Shaft. Or the Borg Warner Velvet Drive Transmission. When measured with a tape measure it will look just under 6 Ã‚Â¼ inches, but the plate is actually 6.18 Inches! Mounting bolt hole center 5.595 Inches Fits Westerbeke Marine Inboard Diesel W-30 and many others. Replaces Westerbeke part # 11618
Marine Drive Damper Flex Plate. The Outside diameter is 13.875", has 8 equally spaced mounting holes and is commonly used on Velvet Drive 71, 72, 73 series for Heavy Duty Diesel applications. Also used on Twin Disc, Paragon and ZF Marine transmissions that have a 26 spline input shaft. This damper has 8 equally spaced holes for mounting to the engine flywheel. Fits 11.5 inch clutch flywheel. This item replaces Borg Warner # 1004-650-001.
Triangular Drive Damper Flex Plate Assembly for Velvet Drive 71 1017 & 72 1018 Series for GM engines with 12.75 Inch flywheel (Starter Will have 1 long and 1 Short Bolt). Works for all small block Ford applications such as PCM and Indmar. Used on volvo Penta GM 305 350 Engines that use the Volvo Penta AQ series Outdrive with the 12.75 Diameter Flywheel Usually 1989 and earlier. If used on PCM Ford applications note that you will only use one bolt per mounting ear. Common use 6.66" Radius Same as ALTDA-106, except with cut Off rounded ears; 26 Spline. This item replaces Borg Warner OEM: 120-8-1446
$129.95... more info
Round Drive Damper Flex Plate Assembly for use on Velvet Drive 71 & 72 with White/Yellow Spring, 13.25" OD Heavy duty version of the ALTDA-107. Used on most GM based marine engines that have a 14 inch flywheel, and many small diesel engines which use a Velvet Drive or Paragon Marine Transmission. OEM: 1004-650-008
$199.95... more info
Drive Damper fits all GM engines with a 14 inch flywheel utilizing a ZF Hurth or Borg Warner 5000 series Transmission. Fits Velvet Drive that have Model Numbers Starting with 2001- and 2002 - Fits Hurth 450A 450V 630A 630V 800A 800V Fits ZF Models 45A 45V 63A 63V 80A 80V This damper dramatically reduces the gear chatter noise found at idle that is an inherent characteristic of the Hurth and Borg Warner 5000 Series Transmission.
Drive Damper fits all engines utilizing a Hurth or Borg Warner 5000 series. This damper dramatically reduces the gear chatter noise found at idle that is an inherent characteristic of the Hurth and Borg Warner 5000 Series Transmission
$399.00... more info
Drive Damper used on a Hurth and Borg Warner 5000 Transmissions with a 454 C.I.D. Crusader engine. This damper reduces the inherent gear chatter sound heard in the ZF and the Velvet Drive 5000 series marine transmissions. Supersedes the following numbers: CRU98248Fits The Following Crusader Applications: CM454XL Note: Genuine Crusader Parts are not always painted "Crusader Blue"
$249.95... more info
Drive Damper Assembly. The diameter is 13.875", and is commonly used on Velvet Drive 71, 72 Heavy Duty Diesel. This item replaces Borg Warner # 1004-650-001.
DRIVESAVER™ Composite Vibration-Reducing Components Absorbs vibration, reduces noise. Saves Your Powertrain. The DRIVESAVER™ provides a flexible, non-metallic barrier between your transmission and propeller shaft. This barrier reduces drivetrain vibration, resulting in reduced noise to you, your crew and the water. As a result, you and your vessel are more efficient in a quieter environment. 4 in. Globe DrivesaverFits Velvet Drive/Borg Warner 1017 (71C) 1:1 transmissions 1023 70C 71CFor use with Crusader 4500 SeriesFor use with Hurth/ZF HBW models 5 10 15 15V 18 20 30 35 50 100 125 150 150A 150V 220 250Newage PRM DeltaFlange diameter 4 in.Number of bolts 4Bolt diameter 3/8 in.Bolt circle 3 1/4 in.Pilot diameter 2 1/2 in.Coupling diameter 5 in.Coupling thickness 1 in.Packaged weight 1.75lbDesigned of elastomer the Drivesaver installs between the transmission and propshaftAbsorbs shock vibration and reduces noise generated from the propshaft making for a smooth quiet rideBlocks electrical current from the water preventing electrolysis on the engine and transmissionFor additional drive train protection the Drivesaver also acts as a sacrificial device if you hit a submerged rock or logThe Drivesaver absorbs the shock of the collision breaks apart and leaves your costly transmission and engine intact
DRIVESAVER™ Composite Vibration-Reducing Components Absorbs vibration, reduces noise. Saves Your Powertrain, this acts as a breakaway in extreme conditions and can save your transmission by acting like a fuse for your drivetrain. The DRIVESAVER™ provides a flexible, non-metallic barrier between your transmission and propeller shaft. This barrier reduces drivetrain vibration, resulting in reduced noise to you, your crew and the water. As a result, you and your vessel are more efficient in a quieter environment. Fits Borg Warner Velvet-Drive 1004, 1005, 1013, 1014, 1017, 1018, 2001, 2002, and 72 C Transmissions Flange Diameter: 5" Number of Bolts: 4 Bolt Diameter: 0.4375" Bolt Circle: 4.25" Pilot Diameter: 2.5" Coupling Diameter: 6" Coupling Thickness: 1" Torque Rating (foot pounds): 675 "Plus Rated" (foot pounds): 1600
ZF 3313316005 Damper Plate Vulcan Torflex 1000 13.875" Outside Diameter For SAE 11-1/2 inch flywheel Used with ZF 220 630 and 800 model transmissions 26 Spline
$500.00... more info
Drive damper for the very popular ZF Marine Transmissions for Diesel Engines. Has a 25 spline hub and a 13.875" outside diameter. This has been laying around a while but is Brand New. Extra shipping applied on this item due to the weight.
$459.95... more info
Copyright © 2021 Basic Power Industries.