Part # & Price | Description |
MPI747-2000
$11.95
| Flange Transom Mounting Rigging 2 Inch Black
2"" inside diameter, black Transom Mounting Flange ideal for securing outboard hose and cable conduit to transom.
Threaded molded plastic grips conduit securely.
Uses 2 Inch Rigging Hose
|
|
THAR-1-DP
$89.95
| ANCHOR MASTER Complete Anchor Retrieval System
The Ultimate Anchor Retriever
The ANCHOR MASTER™ was the first complete buoy & ring anchor
retriever system offered nationally to the boating consumer. It is
still the standard that all copies are measured against with superior
quality and U.S. manufactured components.
The ANCHOR MASTER™ allows a boater to easily and safely retrieve the
anchor. This product eliminates all the hard work pulling up an anchor
and all the pain to the back and hands from doing that work. It also
eliminates the danger of falling overboard while pulling that heavy
load.
System includes: 12" Buoy, Stainless Steel Hook & Ring & Rope and handles up to 20lbs fluke style anchors.
To retrieve your anchor with the ANCHOR MASTER™:
1) Slip the ring around your anchor line and fasten the ring ends into the clip hook which is attached to the rope and buoy.
2) Drop the ANCHOR MASTER™ into the water and motor towards the anchor.
3) Run past the anchor at the speed of 6-8 knots. The buoy will
mostly submerge until the buoyancy of the buoy raises the anchor.
4) When the anchor is fully raised into the ring, the buoy will pop
to the surface. The ring will hold the anchor at the surface.
5) Slowly return to the buoy while you are retrieving the loose rope.
6) Carefully lift the buoy and anchor into your boat.
The ANCHOR MASTER™ was the first complete and ready to use anchor
retriever system on the market! Furthermore, it uses the most foolproof
method of retrieving your anchor - no springs to malfunction, no plastic
parts to break, no device to feed your anchor line through. The ANCHOR
MASTER™ utilizes all stainless steel hardware for a durable,
non-corrosive system.
|
|
THCB-2
$8.95
| Cable Boot 2 Inch Vinyl Black Marine
2" Marine Cable Boot This is truly a functional motor well cable boot that is easy to install. No longer is it necessary to split or cut your motor well boot to pass cables through. This cable boot provides a fully open area to pass wiring and cables through and when rigging is complete simply pull cable tie snug around wires and cable to complete installation.
The cable boot is constructed of rugged black vinyl that resists ultraviolet rays, gasoline and oil. Other manufacturer boots are made of rubber which will degrade in the marine environment. This cable boot is available in three sizes to cover all installation requirements.
Aftermarket kits are available that contain a cable boot and a cable boot reinforcing ring for maximum security in mounting.
|
|
THCB-4
$7.95
| Cable Boot 4.5 Inch Vinyl Black Marine
4-1/2" Marine Cable Boot This is truly a functional motor well cable boot that is easy to install. No longer is it necessary to split or cut your motor well boot to pass cables through. This cable boot provides a fully open area to pass wiring and cables through and when rigging is complete simply pull cable tie snug around wires and cable to complete installation.
The cable boot is constructed of rugged black vinyl that resists ultraviolet rays, gasoline and oil. Other manufacturer boots are made of rubber which will degrade in the marine environment. This cable boot is available in three sizes to cover all installation requirements.
Aftermarket kits are available that contain a cable boot and a cable boot reinforcing ring for maximum security in mounting.
|
|
THFLX-75
$1.25
| Flexible Marine Sleeving 3⁄4 Inch diameter, Sold by the Foot T-H Flex
T-H FLEX™ is a lightweight, braided jacketing for bundling and protecting wires, cables and hoses in a marine environment. Braided from high temperature yarns, T-H FLEX™ offers total protection for wire and cable assemblies. The unique expansion characteristics makes T-H FLEX™ easy to slip on. Only a few sizes are needed to cover a large diameter range, since each size of T-H FLEX® expands up to four times its normal diameter. The sleeving cuts easily and cleanly with a hot knife and once installed, will beautify and protect any wire, hose or cable application. Lightweight Protective SleevingProtects Wire, Cables and HosesBraided from High Temperature YarnsChemical ResistantSimplifies and beautifies any rigging application3/4" diameter, sold by the foot
|
|
THGDP-1-CB
$9.95
| Garboard Marine Drain Plug and Base Chrome Brass
Garboard Marine Drain Plug Chrome Chrome Plated BrassMuch more attractive than bronze and will not turn greenReplaces older bronze fittings with universal hole patternSalt Water and UV ResistantFits 1" HoleFlange diameter is 2"Plug diameter is 1/2" NPTPlug has square top for wrench or socket wrench
|
|
THGHB-1
$8.95
| Grab Handle - Molded - Black
Black Stylish Molded Boat Grab Handles
- Molded, UV-resistant grab handles
- Soft overmold on firm handle
- Textured for sure grip
- Rubberized ergonomic feel
- Hidden fasteners
- Center of screw to center of screw measures 7.25 inches
|
|
THGHB-1FW
$8.95
| Grab Handle - Fish White
Fish White Stylish Molded Boat Grab Handles
- Molded, UV-resistant grab handles
- Soft overmold on firm handle
- Textured for sure grip
- Rubberized ergonomic feel
- Hidden fasteners
- Center of screw to center of screw measures 7.25 inches
|
|
THKS-1
$27.95
| SAF-T-STOP - Ignition Kill Switch - Single Outboard
SAF-T-STOP™ - Ignition Kill Switch - Single Outboard
For all (single) outboard installations. Meets requirements of existing laws covering mandatory use of emergency stop switches. Extra strong, coiled, self-retracting lanyard. Black matte finish for attractive appearance. Mounts in a 1-1/2" diameter hole. Overall dimensions of switch housing are 2-3/4" x 2" and requires 1-1/2" behind panel.
|
|
THMSS-1-DP
$34.95
| MOTOR STIK Outboard Motor Support - Pair in Clam Package
MOTOR STIK™ Outboard Motor Support
Pair (for one outboard motor)
- Fits Over Trim Rams
- Supports Your Outboard While Trailering
- Takes the Pressure Off of Hydraulic System
- Most Outboards 150hp and Up
- Strong Aluminum Tubing with Molded Ends
- Safe for Salt or Fresh Water
NOTE - Some Yamaha motors have a grease fitting on the port side ram. Use a single Motor Stik™ on the starboard side only in this application
|
|
THQF-1K-DP
$16.95
| Quick Flush Outboard Engine Flush Kit Complete Kit Johnson Evinrude
Quick Flush™ Outboard Flush Fitting Complete Kit for Johnson/Evinrude T-H Marine introduces a quick and easy way to flush any outboard equipped with a flushing port. No more removing the plug and twisting hoses to flush. Replace the plug with the Quick Flush™ and snap the hose on and off. Normal operating watter pressure keeps the valve sealed when using engine. Check out these features: Makes flushing outboard quick and easyUnique Patented slide valve replaces outboard flushing port plugO-ring seal closes off port when operating engineQuick connect on hose snaps onto valve for flushingNo plug to remove and no difficult turning of hose into portTakes the hassle out of flushing your outboardFits all outboards equipped with a flushing portKit consists of Patented slide valve, hose quick connector, and washer
|
|
THQF-2K-DP
$29.95
| Quick Flush Outboard Engine Flush Kit Complete Kit Mercury Yamaha
Quick Flush™ Outboard Flush Fitting Complete Kit for Mercury, Yamaha and other outboards T-H Marine introduces a quick and easy way to flush any outboard equipped with a flushing port. No more removing the plug and twisting hoses to flush. Replace the plug with the Quick Flush™ and snap the hose on and off. Normal operating watter pressure keeps the valve sealed when using engine. Check out these features: Makes flushing outboard quick and easyUnique Patented slide valve replaces outboard flushing port plugO-ring seal closes off port when operating engineQuick connect on hose snaps onto valve for flushingNo plug to remove and no difficult turning of hose into portTakes the hassle out of flushing your outboardFits all outboards equipped with a flushing portKit consists of Patented slide valve, hose quick connector, and washer
|
|
THRFK-1-DP
$35.95
| Rigging Flange Kit 2 Inch Rigging Hose Black Marine with Bulkhead Fitting
Outboard marine rigging flaange kit fits moat all outboards and makes a clean installation by covering the myriad of hoses and cables going from your boat to the motor. The kit includes 1 bulkhead fitting and 4 feet of 2 Inch rigging hose. Perfect for most applications. Easily cuts to length.
|
|
THSS-1-DP
$14.95
| Steer - Stop - Steering Lock for Hydraulic Steering Systems 4 Inch
4" Steer-Stop™ - Steering Lock for Hydraulic Steering Systems
Locks Hydraulic Steering when Trailering
T-H Marine developed the first steering stop available for outboards. Outboards equipped with hydraulic steering from "wandering" when trailering. Units clip onto hydraulic steering rams on either side of outboard to keep engine straight and prevent damage to motor supports. Cord keeps units together when stowed and aids removal.
- Locks hydraulic steering when trailering
- Fits most steering cylinder rods on outboard engines
- Snaps over outboards hydraulic steering cylinder rods
- Helps keep engine centered during transport.
- Protects steering system, outboard, and motor supports
- Includes cord to connect units for storage and to aid in removal
- Simple to take on and off
|
|
THTSP-1
$22.95
| Transom Support Plate for Outboard Transom Protection
Transom Support Plate
Distributes Outboard Engine Weight to Protect Your Transom
- Transom Support Plate made of high quality cast aluminum
- Distributes the stress of the motor mounting bolts to protect the transom
- Simple to install
- Fits top bolt pattern of outboard
- Generic plate with no lettering
A = 15" B = 2" C = 13"
|
|
THTTC-1-DP
$33.95
| Transom Trim Control Unit Push Button Trim Switch
Transom Trim Control Switch / Hydraulic Jack Plate Switch
Put a trim switch or hydraulic jack plate anywhere you want with this
versatile switch. The Transom Trim Control Switch provides a
weatherproof tilt control system at the stern area of the boat to
facilitate placing motor support in position with one person. Switch can
also be used for remote adjustment of hydraulic jack plates. The switch
housing is molded black plastic with raised white letters and may be
mounted on any flat surface, comes with 18" pigtail wire and
installation instructions.
- Trim switch for outboards or stern drives
- Hydraulic jack plate switch
- Puts tilt & trim control anywhere you want it
- Waterproof push button switches
- UV stable molded housing
|
|
THTW-2-DP
$40.95
| Transom Wedge - Pair
Outboard Transom Wedges - Add 5 Degrees of Tuck
These transom wedges fit all standard outboard engines. Cast aluminum
construction allows for full, positive contact between engine bracket
and transom. Adds 5 degrees of tuck to transom angle.
- High quality, cast aluminum
- Adds 5 degrees of tuck (negative tilt) to engine
- Improves performance for boats with insufficient transom angle
- Improves boat planing at low speeds
- Fits All Standard Outboard 4-Bolt Patterns
- Full Contact Between Outboard Engine Bracket and Boat Transom
- 2-1/4âââ¬Ã Wide, 11-1/4âââ¬Ã Long
|
|
THZRS-1
$49.95
| Zippered Marine Rigging Sleeve 48 Inch Long
Stylish Zippered 48" Marine Rigging Sleeve Protect your cables and hoses in a marine environment with this easy to remove rigging sleeve. Made of rugged Sunbrella® fabric, this sleeve will withstand the elements and resist fading. Easily zips on and off to access cables of hoses when needed. Ends are secured with cable ties sewn into pockets. Zips On and Off to Protect Cables and HosesRugged Sunbrella® Weather & UV ResistantEnds are Secured with Cable Ties
|
|