This Is A Secure Site
 |  |
Test Equipment, Tools for Chrysler Outboards
|
| |||||
|
Trigger Tester, Outboard Motors Part Number: CDI511-9710 Weight: 1.1 Price: $62.95 Quantity in Basket: none | ||||
Trigger Tester Ideal for testing Mercury/Mariner triggers, Chrysler/Force triggers and Chrysler pre-amp and hall effect sensors, OMC 1988 and up V6 Quick Start timer bases. Also used on OMC OIS ignition, EFI. Great for comparing coils on an engine to determine possible coil failure. 
| |||||
|
| |||||
|
Spark Gap Tester, Neon Indicator Part Number: CDI511-9764 Weight: 0.4 Price: $15.95 Quantity in Basket: none | ||||
|
Sealed 1 Cyl. In-Line Neon Spark Gap Tester. Ideal for personal watercraft. Sealed design is an added safety factor that further reduces the possibility of igniting gas fumes, especially in the hull of a PWC. Good for checking spark on running engine.
| |||||
|
| |||||
|
Spark Gap Tester, Adjustable Part Number: CDI511-9766 Weight: 1.3 Price: $54.95 Quantity in Basket: none | ||||
|
Enclosed 8 Cyl. Adjustable Spark Gap Tester. Has heavy duty wire for mounting in any position. Helps reduce possibility of igniting
gas fumes. (Wires not included) Replaces 91-850439-1, 91-850439T and 91-850439T1 Tech Sheet (pdf)
| |||||
|
| |||||
|
Piercing Probe Set Part Number: CDI511-9770 Weight: 0.5 Price: $65.95 Quantity in Basket: none | ||||
|
Piercing Probe Set No need to disconnect harness or wires. Fully insulated probes have a spring loaded clamp with a tiny stainless steel pin that self centers and punctures the insulation. (Hole will normally reseal itself when the wire heats up.) Ideal for taking DVA readings on all engines and Jet Drive systems. This set is highly recommended for use with all meters and peak reading adapters. Set contains 1 Red and 1 Black probe.
| |||||
|
| |||||
|
DC Ampmeter Adapter Part Number: CDI511-9772 Weight: 0.8 Price: $48.95 Quantity in Basket: none | ||||
|
Ammeter Adapter Used with Fluke multimeters to measure amperage output of the charging system or starter draw amperage. Recommended for use with digital multimeters. Range 1 to 400 amps as 1 millivolt to 4 volts.
| |||||
|
| |||||
|
DVA Peak Voltage Adapter Part Number: CDI511-9773 Weight: 0.5 Price: $69.95 Quantity in Basket: none | ||||
|
Peak Reading DVA Voltage Adapter for all Fluke digital volt meters. The readings will be close to the Stevens CD77 and Merc-Otronic specs. Ideal companion with Piercing Probe Set CDI511-9770. (See application chart in the Troubleshooting Guide for readings on OMC, Mercury, and Chrysler/Force.)
| |||||
|
| |||||
|
DVA Peak Voltage Adapter without leads Part Number: CDI511-9773NL Weight: 0.5 Price: $58.95 Quantity in Basket: none | ||||
|
This is a Peak Reading DVA Voltage Adapter for all Fluke digital volt meters. This adapter does not include the leads. If you require one with leads, please order CDI511-9773. The readings will be close to the Stevens CD77 and Merc-Otronic specs. Ideal companion with Piercing Probe Set CDI511-9770. (See application chart in the Troubleshooting Guide for readings on OMC, Mercury, and Chrysler/Force.)
| |||||
|
| |||||
|
Load Resistor Part Number: CDI511-9775 Weight: 0.1 Price: $13.95 Quantity in Basket: none | ||||
| Load Resistor To load the output of ignition modules when testing ignition coils. Used for testing DVA outputs from power packs and switch boxes. Replacement for Stevens PL88. | |||||
|
| |||||
|
Noise Filter Adapter Part Number: CDI511-9788B Weight: 0.1 Price: $52.95 Quantity in Basket: none | ||||
| 2 cycle noise filter used with Fluke 88 meter with RPM pickup, P/N 518-RMP80, to reduce outboard noise interference for inductive pickup applications. | |||||
|
| |||||
|
Spark Tester Wire Part Number: CDI511-9902 Weight: 0.5 Price: $16.95 Quantity in Basket: none | ||||
| 7" Extension Wire for use with the CDI511-9766 Spark Gap Tester (Set of 4) | |||||
|
| |||||
|
Spark Tester Wire Part Number: CDI511-9903 Weight: 0.7 Price: $18.95 Quantity in Basket: none | ||||
| 24" Extension Wire for use with the CDI511-9766 Spark Gap Tester (Set of 4) | |||||
|
| |||||
|
Fluke Multimeter Part Number: CDI518-116 Weight: 2.4 Price: $265.95 Quantity in Basket: none | ||||
|
| |||||
|
| |||||
|
Fluke 88 Meter Kit with DVA Adapter Part Number: CDI518-88 Weight: 5.3 Price: $631.95 Quantity in Basket: none | ||||
|
Measures 2 and 4 stroke RPM ranges, volts, ohms, amperage,
dwell, and injector pulse width. It has the capability of recording maximum and minimum RPM and volts. Backlight display readout is easy to-read in dim light. Offers specialized functions like RPM, duty cycle, dwell, relative change, lo-ohms and smoothing. Complete with deluxe test leads, probes and clips. Packaged in a battle-tough carrying case.
| |||||
|
| |||||
|
Thermomelt Temp Stiks, 125°F Part Number: CDI519-T125 Weight: 0.1 Price: $19.95 Quantity in Basket: none | ||||
|
Stevens Thermomelt Temp Stiks, 125°F Long lasting Temp Stiks provide a quick and reliable means to check cooling systems. With engine warmed up, the temp stik is used like a crayon to make a mark on the head or block. The mark will appear dull and chalky. On a typical engine, the CDI-T125 (125°) should melt, turning liquid and glossy in appearance. If it does not, the engine is running too cold. A mark made with the CDI-T163 (163°) should not melt. If it does, the engine is running too hot.
| |||||
|
| |||||
|
Thermomelt Temp Stiks, 163°F Part Number: CDI519-T163 Weight: 0.1 Price: $19.95 Quantity in Basket: none | ||||
|
Stevens Thermomelt Temp Stiks, 163°F Long lasting Temp Stiks provide a quick and reliable means to check cooling systems. With engine warmed up, the temp stik is used like a crayon to make a mark on the head or block. The mark will appear dull and chalky. On a typical engine, the CDI-T125 (125°) should melt, turning liquid and glossy in appearance. If it does not, the engine is running too cold. A mark made with the CDI-T163 (163°) should not melt. If it does, the engine is running too hot.
| |||||
|
| |||||
|
Gearcase Filler Part Number: CDI551-33-1 Weight: 6.1 Price: $104.95 Quantity in Basket: none | ||||
|
Gearcase Filler With Check Valve A new design in gearcase fillers makes it easier to fill or flush gearcases. The check valve venting system helps prevent spilling any gear lube. The check valve on the vent allows you to remove the filler nozzle without loosing any appreciable amount of lubricant. Includes CDI551-33CV E-Z Fill®. Replaces Stevens S33. Non-corrosive plastic container. Sturdy teardrop design resists tipping over.
| |||||
|
| |||||
|
Adaptor, Metric, Grease Filler Part Number: CDI551-334M Weight: 0.1 Price: $6.95 Quantity in Basket: none | ||||
|
Metric Adapter for Grease Filler Replaces 519-34M, 551-33M, 551-34M For all motors except Suzuki. | |||||
|
| |||||
|
Filler Vent Check Valve Part Number: CDI551-33CV Weight: 0.4 Price: $16.95 Quantity in Basket: none | ||||
|
Filler Vent Check Valve Calibrated check valve creates airlock to keep lube from running out while you install drain plug. Includes 4’ Hose. A must for all shops! Included with CDI551-33GF.
| |||||
|
| |||||
|
Pressure, Vacuum Tester Part Number: CDI551-34PV Weight: 2.2 Price: $169.95 Quantity in Basket: none | ||||
|
Pressure/Vacuum Tester Repairable metal unit does both vacuum and pressure testing. Combination unit that does pressure and vacuum testing in one unit. Replaces S34 and V34 testers. Includes CDI551-34TN with hose.
| |||||
|
| |||||
|
Threaded Nozzle, Pressure-Vacuum Tester Part Number: CDI551-34TN Weight: 0.1 Price: $6.95 Quantity in Basket: none | ||||
| Threaded Nozzle Fits and is included in CDI551-34PV Pressure/Vacuum Tester. | |||||
|
| |||||
|
Flywheel Holder Part Number: CDI551-5110 Weight: 3.3 Price: $78.95 Quantity in Basket: none | ||||
| Flywheel Holder. New design has a high tensil strength, poly coated, woven belt for a more secure grip of flywheel. Longer handle provides a more comfortable grip for more leverage with less effort. | |||||
|
| |||||
|
Pin Tool Set Part Number: CDI553-2700 Weight: 0.5 Price: $58.95 Quantity in Basket: none | ||||
|
Amphenol Pin Tool Set Set contains one each of CDI553-2697 (insertion), CDI553-2698 (pin removal), and CDI553-2699 (socket removal) tools.
| |||||
|
| |||||
|
Amp Pin Removal Tool Part Number: CDI554-9706 Weight: 0.1 Price: $16.95 Quantity in Basket: none | ||||
| Amp Pin Removal Tool Used to remove the connector pins in the ignition system on Chrysler/Force engines using the Prestolite type ignitions. Also used on Mercury TPI sensor connectors. | |||||
|
| |||||
|
Bullet Connector Kit Part Number: CDI911-9783 Weight: 0.1 Price: $8.95 Quantity in Basket: none | ||||
| Bullet Connector Kit Contains: 10 each Male Bullet with Boots, and 10 Female Bullets with Sleeves. Contains 10 pieces each of the male, female connectors and sleeves. | |||||
|
| |||||
|
Propeller Wrench Set, Mercruiser, Mercury, Mariner, Force, Honda, 1.0625" Part Number: GLM90065 Weight: 1 Price: $8.95 Quantity in Basket: none | ||||
|
1-1/16" Propeller Wrench Kit (blue) for Mercury/Mariner/Force V4 & V6, 75, 90, 100, 115, 125, 135, 150, 175, 200, 225, 250 HP; all Mercruiser; Honda BF75-BF130 comes with GLM21271 OEMs: Mercury: 91-8218871T1; Honda: 89-89206-ZW7-000AH
| |||||
|
| |||||
|
Propeller Wrench Kit, Mercury, Mariner, Force, 0.3125" Part Number: GLM90066 Weight: 1 Price: $4.95 Quantity in Basket: none | ||||
|
5/16" Propeller Wrench Kit (red) for Mercury, Mariner and Force Outboard 30-65 HP, 70 HP 3 cylinder 1989 and older, 15-25 HP 4 stroke OEM: 91-856639A1 | |||||
|
| |||||
|
Oil Pump, Lower Unit, Quart Part Number: MAL9-81002 Weight: 0.18 Price: $10.95 Quantity in Basket: none | ||||
| |||||
